User Tools

Site Tools


extended_g-code_table

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
extended_g-code_table [2017/11/09 11:44]
Matthew Upp
extended_g-code_table [2018/09/15 00:56] (current)
Matthew Upp
Line 49: Line 49:
  
 ==== M561 - Change Hotend Thermistor Type ==== ==== M561 - Change Hotend Thermistor Type ====
-<code+=== Default === 
-M561 P0         ​;Change to Default or EPCOS 100K +<file gcode change_hotend_thermistor_type_default.gcode> 
-M500            ;Save EEPROM +; G-Code generated by Matthew Upp 
-Reboot printer to complete the process +; Change thermistor type to Default or EPCOS 100K and saves to EEPROM 
-             Or +; Please add a blank line to the end of the file while editing. DokuWiki Code Blocks deletes blank lines at the end of the block but g-code files should end with a single blank line at the end. 
-M561 P1         ​;Change to 104GT-2 or 104NT-4-R025H42G (may report as 104GT) +; 
-M500            ;Save EEPROM +M561 P0 ; Change to Default or EPCOS 100K 
-Reboot printer to complete the process +M500 ; Save to EEPROM 
-</code>+Reboot ​the printer to complete the process 
 +</​file>​ 
 + 
 +=== 104GT-2 === 
 +<file gcode change_hotend_thermistor_type_104gt-2.gcode>​ 
 +; G-Code generated by Matthew Upp 
 +; Change thermistor type to 104GT-2 or 104NT-4-R025H42G (may report as 104GT) and saves to EEPROM 
 +; Please add a blank line to the end of the file while editing. DokuWiki Code Blocks deletes blank lines at the end of the block but g-code files should end with a single blank line at the end. 
 +;              ​ 
 +M561 P1 ;Change to 104GT-2 or 104NT-4-R025H42G (may report as 104GT) 
 +M500 ; Save to EEPROM 
 +
 +Reboot ​the printer to complete the process 
 +</file>
  
 ==== M561 B - Change Heat Bed Thermistor Type ==== ==== M561 B - Change Heat Bed Thermistor Type ====
Line 90: Line 103:
 Reboot printer to complete the process Reboot printer to complete the process
 </​code>​ </​code>​
 +
 +==== M562 Z ====
 +<file gcode invert_z-axis.gcode>​
 +; G-Code generated by Matthew Upp
 +; Invert Z-Axis ​
 +; Possibly helpful if you need to invert the Z-axis after switching to a NEMA 17 motor and lead screw
 +; for Malyan M200 & MP Select Mini
 +
 +; Lines with only a semicolon are for making line separations only
 +; Please add a blank line to the end of the file while editing. DokuWiki Code Blocks deletes blank lines at the end of the block but g-code files should end with a single blank line at the end.
 +
 +
 +M106 S1 ; turn fan off in case it was already on
 +M0 S2 ; wait 2 seconds
 +M106 S245 ; turn fan on to signify start
 +
 +;  ​
 +M562 Z ; Invert Z-Axis
 +M500 ; Save currently loaded settings to EEPROM
 +
 +;
 +G28 Z ; home Z to verify the Z-axis is inverted
 +G1 Z10 F1000 ; Move Z-Axis up 10mm to signify completion
 +M107 ; turn fan off to signify completion
 +M84 ; disable motors
 +M0 S2 ; wait 2 seconds
 +;
 +; You may need to reboot the printer to complete the process
 +</​file>​
  
 ---- ----
extended_g-code_table.1510256657.txt.gz · Last modified: 2017/11/09 11:44 by Matthew Upp