Differences

This shows you the differences between two versions of the page.

--- firmware:ui_controller [2017/06/09 09:54]
Matthew Upp
+++ firmware:ui_controller [2020/07/30 17:22] (current)
Matthew Upp
@@ Line 4: / Line 4: @@
 ----
+<WRAP center round alert 100%>
-<WRAP center round alert 95%>
 <WRAP group>
 <WRAP column half>
-<wrap lo><wrap em>If you received a Select Mini V1 or V2, black or white and the UI looks like the photo, do not update the firmware with any currently available firmware version. Some V1's & V2's, white or black do <wrap hi>__NOT__</wrap> use the same firmware as previous V1 & V2's. \\
+<wrap lo><wrap em>If you received a Select Mini V1 or V2, black or white and the UI looks like the photo, do <wrap hi>__NOT__</wrap> update the UI Controller firmware with any currently available firmware version. Some V1's & V2's, white or black do <wrap hi>__NOT__</wrap> use the same firmware as previous V1 & V2's. \\
-If your Select Mini has Motion Controller version 31+ or higher pre-installed, do <wrap hi>__NOT__</wrap> use V1 Motion Controller firmware. \\
+\\
-If your Select Mini has UI Controller version 106.2 or similar pre-installed, do <wrap hi>__NOT__</wrap> use V1 UI Controller firmware.
-</wrap></wrap>
+If your Select Mini has UI Controller version 106.2, 156.2, or similar pre-installed, do <wrap hi>__NOT__</wrap> use V1 UI Controller firmware which is any versions 33 through 42. \\
+\\
+I know all that is a bit confusing and may not make sense to anyone other than myself. Basically if you have a Select Mini V2 or V1 that has the UI seen in the pictures below/adjacent, don't update the UI/LCD Controller firmware. \\
+</wrap></wrap>
 </WRAP>
 <WRAP column half>
-{{ :wiki:ui_controller_v106.2_collage.jpg?200 |}}
+<WRAP group>
+<WRAP column half>
+{{gallery> :wiki:mpsm_new_ui_example_collage_20170623.jpg?&200x200&1&lightbox }}
+</WRAP>
+<WRAP column half>
+{{gallery> :wiki:collage_2017-09-25_07_14_52.jpg?&200x200&1&lightbox }}
+</WRAP>
 </WRAP>
 </WRAP>
+</WRAP>
+</WRAP>
+<WRAP center round info 100%>
+<wrap lo>
+Do you have a black screen after falling victim to updating the firmware after watching a video or maybe you outright ignored the warnings? You can contact me in one of the following online community groups so that we may schedule a time to get your printers display back to the way Monoprice intended it to be. \\
+[[https://facebook.com/groups/1717306548519045/|MP Select Mini Owners Facebook Group]] - Name: [[https://www.facebook.com/matthewupp|Matthew Upp]] \\
+[[https://reddit.com/r/MPSelectMiniOwners/|MPSelectMiniOwners subreddit]] - User: [[https://www.reddit.com/user/tiny_tim_|tiny_tim_]] \\
+[[https://plus.google.com/communities/116802523766279866092|Monoprice MP Select Mini Google+ Community]] - Name: [[http://google.com/+MatthewUpp|Matthew Upp]]\\
+//(This is only a temporary fix. When the V1's have definitely stopped shipping and fully tested firmware for the V2 is released, this process will not need to be done.)//</wrap>
 </WRAP>
-**Link to firmware:** http://firmware.mpselectmini.com
 <wrap em>**UPDATING THE FIRMWARE IS NOT SUPPORTED BY MONOPRICE** </wrap>\\
@@ Line 31: / Line 53: @@
 <wrap em><wrap lo>If you have UI Controller firmware version 34 or higher you do NOT need to update the firmware to enable WiFi.</wrap></wrap>
+**[[downloads:start|Link to V1 firmware]]**
 <wrap hi>//Note: If you have trouble updating, please format microSD card or use another microSD card and try again. Try a microSD card that is 4GB or less formatted with FAT. The printer can be picky at which cards it will update from so try a few cards.//</wrap>
+----
+===== UI Controller Firmware (lcd.bin) Update Process =====
   - Disconnect USB cable
   - Copy the lcd.bin file to the micro SD card and put into printer while powered off
@@ Line 43: / Line 70: @@
   - Delete lcd.bin from micro SD card if printer keeps restarting.
+----
 ==== Troubleshooting ====

MP Select Mini / Malyan M200 3D Printer

User Tools

Site Tools

Differences

Page Tools