User Tools

Site Tools


g-code

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
g-code [2017/06/14 19:19]
Matthew Upp
g-code [2018/01/17 09:25] (current)
Matthew Upp
Line 18: Line 18:
   * [[g-code#​microSD_card|MicroSD Card]]   * [[g-code#​microSD_card|MicroSD Card]]
   * [[g-code#​wifi|WiFi]]   * [[g-code#​wifi|WiFi]]
-\\ 
  
  
 ===== USB ===== ===== USB =====
 +The printer uses a Micro-B USB 2.0 cable. When connecting to the printer make sure to use a good quality cable that is meant for data transfer. Using a Micro-B USB cable that came with your phone, tablet, or even the included USB cable may work but are usually not the best cables to trust for reliable & consistent data connection between the printer and the other device such as a laptop, desktop computer, or Raspberry Pi. Using a Micro-B USB 2.0 cable with a [[https://​en.wikipedia.org/​wiki/​Ferrite_bead|ferrite bead]] may help but should not be necessary.
 +
  
 Sending G-code over USB is not the only way to send G-code but is probably the easiest. Many slicer programs have the ability to send G-code to the printer via USB. See your slicer documentation for this feature. \\ Sending G-code over USB is not the only way to send G-code but is probably the easiest. Many slicer programs have the ability to send G-code to the printer via USB. See your slicer documentation for this feature. \\
  
 Programs like Printrun (Pronterface) and Repetier-Host are easy to use and don't require much set up. There are precompiled versions of Printrun for Windows that can be used without installation and only require selecting the correct COM port to connect to the printer. \\ Programs like Printrun (Pronterface) and Repetier-Host are easy to use and don't require much set up. There are precompiled versions of Printrun for Windows that can be used without installation and only require selecting the correct COM port to connect to the printer. \\
 +
 +
 +<WRAP group>
 +<WRAP column half>
  
 **Cura 15.04.6** \\ **Cura 15.04.6** \\
 [[cura_pronterface|Enable Cura 15.04.6 Pronterface UI]] [[cura_pronterface|Enable Cura 15.04.6 Pronterface UI]]
 +
  
 **Printrun** \\ **Printrun** \\
 http://​www.pronterface.com/​ \\ http://​www.pronterface.com/​ \\
 http://​reprap.org/​wiki/​Printrun \\ http://​reprap.org/​wiki/​Printrun \\
 +
  
 **Repetier-Host** \\ **Repetier-Host** \\
Line 38: Line 45:
 http://​reprap.org/​wiki/​Repetier-Host \\ http://​reprap.org/​wiki/​Repetier-Host \\
 \\ \\
 +
 +</​WRAP>​
 +
 +<WRAP column half>
 +
 +{{youtube>​R1VugOTOoGA?​small}}
 +
 +[[https://​youtu.be/​R1VugOTOoGA|How to send G-Code commands with Pronterface]]
 +
 +
 +</​WRAP>​
 +</​WRAP>​
  
  
Line 62: Line 81:
 ==== Custom Web UI ==== ==== Custom Web UI ====
 You may also send g-code commands using a [[sample_webui#​upload_custom_web_ui|custom Web UI]]. \\ You may also send g-code commands using a [[sample_webui#​upload_custom_web_ui|custom Web UI]]. \\
-More information can be found on the Web UI page.+More information can be found on the [[sample_webui|Web UI page]].
  
g-code.1497467966.txt.gz · Last modified: 2017/06/14 19:19 by Matthew Upp