User Tools

Site Tools


invert_motor_direction

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
invert_motor_direction [2017/11/21 17:25]
Matthew Upp
invert_motor_direction [2019/04/02 07:51] (current)
Matthew Upp
Line 5: Line 5:
 ---- ----
  
 +[[invert_motor_direction#​m562_gcode_files|See below for downloadable gcode files that can be ran from a microSD card.]]
  
 ===== Extruder ===== ===== Extruder =====
 <​code>​ <​code>​
-M562 E                ;Inverts Extruder/​Feeder Mechanism motor direction +M562 E     ​; Inverts Extruder/​Feeder Mechanism motor direction 
-M500                  ;Saves changes to EEPROM+M500       ​; Saves changes to EEPROM
 Reboot printer to complete the process (turn off, then on) Reboot printer to complete the process (turn off, then on)
 </​code>​ </​code>​
Line 16: Line 17:
 ===== X-Axis ===== ===== X-Axis =====
 <​code>​ <​code>​
-M562 X                ;Inverts X-Axis motor direction +M562 X     ​; Inverts X-Axis motor direction 
-M500                  ;Saves changes to EEPROM+M500       ​; Saves changes to EEPROM
 Reboot printer to complete the process (turn off, then on) Reboot printer to complete the process (turn off, then on)
 </​code>​ </​code>​
Line 24: Line 25:
 ===== Y-Axis ===== ===== Y-Axis =====
 <​code>​ <​code>​
-M562 Y                ;Inverts Y-Axis motor direction +M562 Y     ​; Inverts Y-Axis motor direction 
-M500                  ;Saves changes to EEPROM+M500       ​; Saves changes to EEPROM
 Reboot printer to complete the process (turn off, then on) Reboot printer to complete the process (turn off, then on)
 </​code>​ </​code>​
- 
  
 ===== Z-Axis ===== ===== Z-Axis =====
 <​code>​ <​code>​
-M562 Z                ;Inverts Z-Axis motor direction +M562 Z     ​; Inverts Z-Axis motor direction 
-M500                  ;Saves changes to EEPROM+M500       ​; Saves changes to EEPROM
 Reboot printer to complete the process (turn off, then on) Reboot printer to complete the process (turn off, then on)
 </​code>​ </​code>​
 +
 +----
 +
 +\\
 +
 +===== Gcode Files =====
 +
 +
 +==== M562 E ====
 +<file gcode invert_extruder.gcode>​
 +; G-Code generated by Matthew Upp
 +; Invert Extruder
 +; Possibly helpful if you need to invert the extruder after switching to a different type extruder/​feed mechanism
 +; for Malyan M200 & MP Select Mini
 +
 +; Lines with only a semicolon are for making line separations only.
 +; Please add a blank line to the end of the file while editing.
 +; DokuWiki Code Blocks deletes blank lines at the end of the block but 
 +; g-code files should end with a single blank line at the end. 
 +; (It is not a big deal if you don't add the line at the end.)
 +
 +
 +M107 ; turn fan off in case it was already on
 +M106 S237 ; turn fan on to signify start
 +
 +;  ​
 +M562 E ; invert extruder
 +M500 ; save currently loaded settings to EEPROM
 +
 +;
 +M400 ; wait for current moves to finish
 +M107 ; turn fan off to signify completion
 +M84 ; disable motors
 +
 +</​file>​
 +
 +
 +==== M562 X ====
 +<file gcode invert_x-axis.gcode>​
 +; G-Code generated by Matthew Upp
 +; Invert X-Axis ​
 +; for Malyan M200 & MP Select Mini
 +
 +; Lines with only a semicolon are for making line separations only.
 +; Please add a blank line to the end of the file while editing.
 +; DokuWiki Code Blocks deletes blank lines at the end of the block but 
 +; g-code files should end with a single blank line at the end. 
 +; (It is not a big deal if you don't add the line at the end.)
 +
 +
 +M107 ; turn fan off in case it was already on
 +M106 S237 ; turn fan on to signify start
 +;
 +;
 +M562 X ; invert X-Axis
 +M500 ; save currently loaded settings to EEPROM
 +;
 +;
 +G28 X ; home X to verify the X-axis is inverted
 +G1 X60 F1000 ; move X-Axis to center of the bed to signify completion
 +M400 ; wait for current moves to finish
 +M107 ; turn fan off to signify completion
 +M84 ; disable motors
 +
 +</​file>​
 +
 +
 +==== M562 Y ====
 +<file gcode invert_y-axis.gcode>​
 +; G-Code generated by Matthew Upp
 +; Invert Y-Axis ​
 +; for Malyan M200 & MP Select Mini
 +
 +; Lines with only a semicolon are for making line separations only.
 +; Please add a blank line to the end of the file while editing.
 +; DokuWiki Code Blocks deletes blank lines at the end of the block but 
 +; g-code files should end with a single blank line at the end. 
 +; (It is not a big deal if you don't add the line at the end.)
 +
 +
 +M107 ; turn fan off in case it was already on
 +M106 S237 ; turn fan on to signify start
 +
 +;  ​
 +M562 Y ; invert Y-Axis
 +M500 ; save currently loaded settings to EEPROM
 +
 +;
 +G28 Y ; home Y to verify the Y-axis is inverted
 +G1 Y60 F1000 ; move Y-Axis to center of the bed to signify completion
 +M400 ; wait for current moves to finish
 +M107 ; turn fan off to signify completion
 +M84 ; disable motors
 +
 +</​file>​
 +
 +
 +==== M562 Z ====
 +<file gcode invert_z-axis.gcode>​
 +; G-Code generated by Matthew Upp
 +; Invert Z-Axis
 +; Possibly helpful if you need to invert the Z-axis after switching to a NEMA 17 motor and lead screw
 +; for Malyan M200 & MP Select Mini
 +
 +; Lines with only a semicolon are for making line separations only.
 +; Please add a blank line to the end of the file while editing.
 +; DokuWiki Code Blocks deletes blank lines at the end of the block but 
 +; g-code files should end with a single blank line at the end. 
 +; (It is not a big deal if you don't add the line at the end.)
 +
 +
 +M107 ; turn fan off in case it was already on
 +M106 S237 ; turn fan on to signify start
 +
 +;  ​
 +M562 Z ; invert Z-Axis
 +M500 ; save currently loaded settings to EEPROM
 +
 +;
 +G28 Z ; home Z to verify the Z-axis is inverted
 +G1 Z10 F1000 ; move Z-Axis up 10mm to signify completion
 +M400 ; wait for current moves to finish
 +M107 ; turn fan off to signify completion
 +M84 ; disable motors
 +
 +</​file>​
  
  
invert_motor_direction.1511285117.txt.gz · Last modified: 2017/11/21 17:25 by Matthew Upp