This is an old revision of the document!
M562 E ; Inverts Extruder/Feeder Mechanism motor direction M500 ; Saves changes to EEPROM Reboot printer to complete the process (turn off, then on)
M562 X ; Inverts X-Axis motor direction M500 ; Saves changes to EEPROM Reboot printer to complete the process (turn off, then on)
M562 Y ; Inverts Y-Axis motor direction M500 ; Saves changes to EEPROM Reboot printer to complete the process (turn off, then on)
M562 Z ; Inverts Z-Axis motor direction M500 ; Saves changes to EEPROM Reboot printer to complete the process (turn off, then on)
; G-Code generated by Matthew Upp of GigDigit.com ; ; Invert Extruder Motor Direction ; ; This gcode file will work with the following 3D printers: ; Malyan - M100, M200, M300, M310, M320, MA10, MA10 Mini ; Monoprice - MP10, MP10 Mini, MP Mini Delta, MP Select Mini ; ; ; This file is much longer than it needs to be but is like this to ; show what is going on. ; ; If when "printing" this file it does not show as completed on the ; display but the fan pulsed on and off a few times then the invert ; command was successfully ran and saved. You can turn the printer ; off and on to make sure the setting was saved. ; ; Lines with only a semicolon are for making line separations only. ; Please add a blank line to the end of the file while editing. ; DokuWiki Code Blocks deletes blank lines at the end of the block but ; g-code files typically end with a single blank line at the end. ; (It is not a big deal if you don't add the blank line.) ; ; ; BEGIN M107 ; turn fan off in case it was already on M106 S237 ; turn fan on to signify start ; ; ; The next two lines are the only actual commands that are needed to ; invert the extruder motor direction and save. M562 E ; invert extruder M500 ; save the setting to EEPROM ; ; ; PULSE FAN TO SIGNIFY COMPLETION M107 ; turn fan off G4 S1 ; wait 1 second M106 S255 ; fan at full speed G4 P500 ; wait 0.5 seconds M107 ; fan off ; G4 P250 ; wait 0.25 seconds M106 S255 ; fan at full speed G4 P500 ; wait 0.5 seconds M107 ; fan off ; G4 P250 ; wait 0.25 seconds M106 S255 ; fan at full speed G4 P500 ; wait 0.5 seconds M107 ; fan off ; G4 P250 ; wait 0.25 seconds M106 S255 ; fan at full speed G4 P500 ; wait 0.5 seconds M107 ; fan off ; G4 P250 ; wait 0.25 seconds M106 S255 ; fan at full speed G4 P500 ; wait 0.5 seconds M107 ; fan off ; G4 P250 ; wait 0.25 seconds M106 S255 ; fan at full speed G4 P500 ; wait 0.5 seconds M107 ; fan off ; ; M400 ; Wait for current moves to finish M107 ; turn fan off to signify completion M84 ; disable motors ; END
; G-Code generated by Matthew Upp of GigDigit.com ; ; Invert X-Axis Motor Direction ; ; This gcode file will work with the following 3D printers: ; Malyan - M100, M200, M300, M310, M320, MA10, MA10 Mini ; Monoprice - MP10, MP10 Mini, MP Mini Delta, MP Select Mini ; ; This file is much longer than it needs to be but is like this to ; show what is going on. ; ; If when "printing" this file it does not show as completed on the ; display but the fan pulsed on and off a few times then the invert ; command was successfully ran and saved. You can turn the printer ; off and on to make sure the setting was saved. ; ; Lines with only a semicolon are for making line separations only. ; Please add a blank line to the end of the file while editing. ; DokuWiki Code Blocks deletes blank lines at the end of the block but ; g-code files typically end with a single blank line at the end. ; (It is not a big deal if you don't add the blank line.) ; ; ; BEGIN M107 ; turn fan off in case it was already on M106 S237 ; turn fan on to signify start ; ; ; The next two lines are the only actual commands that are needed to ; invert the X-axis motor direction and save. M562 X ; invert x-axis M500 ; save currently loaded settings to eeprom ;END ; ; ; PULSE FAN TO SIGNIFY COMPLETION M107 ; turn fan off G4 S1 ; wait 1 second M106 S255 ; fan at full speed G4 P500 ; wait 0.5 seconds M107 ; fan off ; G4 P250 ; wait 0.25 seconds M106 S255 ; fan at full speed G4 P500 ; wait 0.5 seconds M107 ; fan off ; G4 P250 ; wait 0.25 seconds M106 S255 ; fan at full speed G4 P500 ; wait 0.5 seconds M107 ; fan off ; G4 P250 ; wait 0.25 seconds M106 S255 ; fan at full speed G4 P500 ; wait 0.5 seconds M107 ; fan off ; G4 P250 ; wait 0.25 seconds M106 S255 ; fan at full speed G4 P500 ; wait 0.5 seconds M107 ; fan off ; G4 P250 ; wait 0.25 seconds M106 S255 ; fan at full speed G4 P500 ; wait 0.5 seconds M107 ; fan off ; ; M400 ; Wait for current moves to finish M107 ; turn fan off to signify completion M84 ; disable motors ; END
; G-Code generated by Matthew Upp of GigDigit.com ; ; Invert Y-Axis Motor Direction ; ; This gcode file will work with the following 3D printers: ; Malyan - M100, M200, M300, M310, M320, MA10, MA10 Mini ; Monoprice - MP10, MP10 Mini, MP Mini Delta, MP Select Mini ; ; This file is much longer than it needs to be but is like this to ; show what is going on. ; ; If when "printing" this file it does not show as completed on the ; display but the fan pulsed on and off a few times then the invert ; command was successfully ran and saved. You can turn the printer ; off and on to make sure the setting was saved. ; ; Lines with only a semicolon are for making line separations only. ; Please add a blank line to the end of the file while editing. ; DokuWiki Code Blocks deletes blank lines at the end of the block but ; g-code files typically end with a single blank line at the end. ; (It is not a big deal if you don't add the blank line.) ; ; ; BEGIN M107 ; turn fan off in case it was already on M106 S237 ; turn fan on to signify start ; ; ; The next two lines are the only actual commands that are needed to ; invert the Y-axis motor direction and save. M562 Y ; invert y-axis M500 ; save currently loaded settings to eeprom ;END ; ; ; PULSE FAN TO SIGNIFY COMPLETION M107 ; turn fan off G4 S1 ; wait 1 second M106 S255 ; fan at full speed G4 P500 ; wait 0.5 seconds M107 ; fan off ; G4 P250 ; wait 0.25 seconds M106 S255 ; fan at full speed G4 P500 ; wait 0.5 seconds M107 ; fan off ; G4 P250 ; wait 0.25 seconds M106 S255 ; fan at full speed G4 P500 ; wait 0.5 seconds M107 ; fan off ; G4 P250 ; wait 0.25 seconds M106 S255 ; fan at full speed G4 P500 ; wait 0.5 seconds M107 ; fan off ; G4 P250 ; wait 0.25 seconds M106 S255 ; fan at full speed G4 P500 ; wait 0.5 seconds M107 ; fan off ; G4 P250 ; wait 0.25 seconds M106 S255 ; fan at full speed G4 P500 ; wait 0.5 seconds M107 ; fan off ; ; M400 ; Wait for current moves to finish M107 ; turn fan off to signify completion M84 ; disable motors ; END
; G-Code generated by Matthew Upp of GigDigit.com ; ; Invert Z-Axis Motor Direction ; ; This gcode file will work with the following 3D printers: ; Malyan - M100, M200, M300, M310, M320, MA10, MA10 Mini ; Monoprice - MP10, MP10 Mini, MP Mini Delta, MP Select Mini ; Possibly helpful if you need to invert the Z-axis after switching ; to a NEMA 17 motor and lead screw for Malyan M200 & MP Select Mini ; ; This file is much longer than it needs to be but is like this to ; show what is going on. ; ; If when "printing" this file it does not show as completed on the ; display but the fan pulsed on and off a few times then the invert ; command was successfully ran and saved. You can turn the printer ; off and on to make sure the setting was saved. ; ; Lines with only a semicolon are for making line separations only. ; Please add a blank line to the end of the file while editing. ; DokuWiki Code Blocks deletes blank lines at the end of the block but ; g-code files typically end with a single blank line at the end. ; (It is not a big deal if you don't add the blank line.) ; ; ; BEGIN M107 ; turn fan off in case it was already on M106 S237 ; turn fan on to signify start ; ; ; The next two lines are the only actual commands that are needed to ; invert the Z-axis motor direction and save. M562 Z ; invert Z-axis M500 ; save currently loaded settings to eeprom ;END ; ; ; PULSE FAN TO SIGNIFY COMPLETION M107 ; turn fan off G4 S1 ; wait 1 second M106 S255 ; fan at full speed G4 P500 ; wait 0.5 seconds M107 ; fan off ; G4 P250 ; wait 0.25 seconds M106 S255 ; fan at full speed G4 P500 ; wait 0.5 seconds M107 ; fan off ; G4 P250 ; wait 0.25 seconds M106 S255 ; fan at full speed G4 P500 ; wait 0.5 seconds M107 ; fan off ; G4 P250 ; wait 0.25 seconds M106 S255 ; fan at full speed G4 P500 ; wait 0.5 seconds M107 ; fan off ; G4 P250 ; wait 0.25 seconds M106 S255 ; fan at full speed G4 P500 ; wait 0.5 seconds M107 ; fan off ; G4 P250 ; wait 0.25 seconds M106 S255 ; fan at full speed G4 P500 ; wait 0.5 seconds M107 ; fan off ; ; M400 ; Wait for current moves to finish M107 ; turn fan off to signify completion M84 ; disable motors ; END