User Tools

Site Tools


parts:extruder

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
parts:extruder [2016/09/30 19:30]
Matthew Upp
parts:extruder [2019/11/05 22:15] (current)
Matthew Upp
Line 1: Line 1:
-==== Extruder Replacements ====+~~NOTOC~~ 
 + 
 +====== Extruder ​/ Feed Mechanism ====== 
 + 
 +---- 
 + 
 +The MP Select Mini uses a Right Hand MK8 Extruder. A few acceptable replacements are listed below. Some listings will have a choice of left or right hand model. Be sure to choose "​right"​ or "right hand". \\ 
 +Watch Thomas Sanladerer [[http://​mpselectmini.com/​extruder_calibration|calibrate his extruder]]. 
 + 
 +---- 
 + 
 +===== Direct Replacement ===== 
 +==== Extruder ==== 
 +**GigDigit** - **[[https://​gigdigit.com/​extruder-feed-mechanism-for-mp-select-mini-v1-v2-pro-v3/​|Extruder - Feed Mechanism for MP Select Mini V1, V2, Pro/​V3]]** 
 + 
 +**GigDigit** - **[[https://​gigdigit.com/​extruder-gear/​|Extruder Gear]]** \\ 
 +\\ 
 + 
 +==== Connector ==== 
 +<wrap lo>(Be sure to verify the one you need matches the product pictures as there have been two types used)</​wrap>​ 
 + 
 +**GigDigit** - [[https://​www.mpminidelta.com/​parts/​bowden_tube_connectors|Bowden Connector for New Type Extruder / Feeder Mechanism]] 
 + 
 +**GigDigit** - [[https://​gigdigit.com/​bowden-coupling-connector-pc4-m6/​|Bowden Coupling / Connector - PC4-M6]] 
 + 
 + 
 +---- 
 + 
 +===== Printable ​Replacements ====
 +[[https://​mpselectmini.com/​thingiverse/​extruder|Thingiverse Collection of Extruders for the Mini Delta and Select Mini]] 
 + 
 +---- 
 + 
 +===== Aftermarket Replacements ===== 
 + 
 +**Amazon.com** - [[http://​amzn.to/​2FFUGzE|Redrex Right Hand 1.75mm Filament MK8 Bowden Extruder ]] \\ 
 + 
 +**Amazon.com** - [[http://​amzn.to/​2B8ZMBZ|Anycubic All Metal Right Hand MK8 Extruder (Gold Color)]] \\ 
 +<wrap em><​wrap lo>​**NOTE:​** Requires two M3x20mm screws or two M3x25mm screws and maybe a couple of M3 washers that are not included.</​wrap></​wrap>​ \\ 
 + 
 + 
 +**eBay.com** - [[http://​www.ebay.com/​itm/​361682351894/​|3D Printer MK8 1.75mm Filament Aluminum Alloy Extruder Kit W/ Bracket (Black & Red)]] \\ 
 + 
 + 
 + 
 +<wrap hi>NOTE: This is optional but if you would like to keep the original/​stock extruder gear, you will want to also purchase a 4x10x4mm bearing (examples linked below). The benefit is that you won't have to struggle to remove the existing gear and you won't have to [[http://​mpselectmini.com/​extruder_calibration|recalibrate the extruder]]. Removing the existing gear can be troublesome but applying heat to the gear with a heat gun, lighter, small torch, or similar should make the task a little easier due to the thermal expansion of the gear. This should go without saying but please use a tool or something other than your hands to grasp the gear after heating.</​wrap>​ \\ 
 + 
 +**McMaster-Carr** - [[https://​www.mcmaster.com/#​7804K1/​|Stainless Steel Ball Bearing - Premium Double Shielded, for 4mm Shaft Diameter, 10mm OD]] 
 + 
 +**Amazon.com** - [[http://​amzn.to/​2B8Fmcx/​|uxcell 5 Pcs Double Sealed 4 x 10 x 4mm Deep Groove Ball Bearings L-1040]] \\
  
-**Anycubic All Metal Right Hand MK8 Extruder** \\ 
-https://​amzn.com/​B0196B285I 
  
-**3D Printer MK8 1.75mm Filament Aluminum Alloy Extruder Kit W/ Bracket** \\ 
-[[http://​www.ebay.com/​itm/​3D-Printer-MK8-1-75mm-Filament-Aluminum-Alloy-Extruder-Kit-W-Bracket-Hot-/​361682351894]] \\ 
-[[http://​www.ebay.com/​itm/​3D-Printer-MK8-1-75mm-Filament-Aluminum-Alloy-Extruder-Kit-W-Bracket-66-/​282115508787]] \\ 
parts/extruder.1475263837.txt.gz · Last modified: 2016/09/30 19:30 by Matthew Upp