User Tools

Site Tools


parts:mainboard

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
parts:mainboard [2016/11/01 23:49]
Matthew Upp created
parts:mainboard [2018/09/11 07:38] (current)
Matthew Upp
Line 1: Line 1:
-===== Main Board Replacement ​=====+~~NOTOC~~ 
 + 
 +====== Motion Controller ​Board =====
 + 
 +---- 
 + 
 + 
 +//Jump to the [[parts:​mainboard#​replacements|Replacements]] section for **V1** & **V2** mainboard replacement options.//​ 
 + 
 +===== Information ===== 
 + 
 +<wrap lo><​wrap em>Some of the following information does <wrap hi>​__NOT__</​wrap>​ apply to the Select Mini V2.</​wrap></​wrap>​ \\ 
 +The motion controller board or mainboard is powered by a STM32F103C8T6 "​ARM®Cortex®-M3 32-bit RISC core operating at a 72 MHz frequency"​. See http://​www.st.com/​en/​microcontrollers/​stm32f103c8.html for full specifications. \\ 
 + 
 +There have been more than two variations of the Motion Controller Board but these were minor changes. One example of the minor changes is the stepper drivers originally shipped with each having their own heat sink. Sometime shortly after initial batch of Select Mini's that Monoprice started shipping to customers on May 26, 2016 the stepper drivers shared one heat sink that spanned across all four. The units that shared one heat sink may have also been in the first batch of 500 printers that were shipped. \\ 
 + 
 + 
 +===== V1 ===== 
 +<WRAP group> 
 +<WRAP column half> 
 + 
 +**V1 - Old version** (discontinued as of roughly middle of August 2016) \\  
 +{{:​mp_select_mini-main_board-1.jpg?​500|}} \\ 
 +\\ 
 + 
 + 
 +</​WRAP>​ 
 +<WRAP column half> 
 + 
 +**V1 - Updated version** (middle of August 2016 - present) \\ 
 +//From printer received September 2, 2016// \\ 
 +{{:​mp_select_mini-main_board_rev2.jpg?​500|}} 
 +\\ 
 + 
 + 
 +</​WRAP>​ 
 +</​WRAP>​ 
 + 
 + 
 +A fan header was added to the Motion Controller board. This connector is intended for additional fan for cooling the mainboard. The fan is supposed to start if the mainboard temperature goes above 55C. 
 + 
 +The fan header on the pictured revision will not work without a small hardware modification. The fix requires reversing the small MOSFET (SOT-23) upside down to make it correct (I ASSUME the one adjacent to the fan header). "The design engineer made a mistake that reversed the package"​. The next shipment of machines was supposed to have this correction already applied. Motion Controller firmware version 26 or higher is required to use the additional fan header. There are very limited reports that this fan header works. YMMV 
 + 
 +---- 
 + 
 +===== V2 ===== 
 +<WRAP group> 
 +<WRAP column half> 
 + 
 +**V2** (newer version) \\ 
 +//April 16, 2018// \\ 
 +{{:​parts:​m200_mainboard-20180416_211317.jpg?​500|}} \\ 
 +\\ 
 + 
 + 
 +/* 
 + 
 +</​WRAP>​ 
 +<WRAP column half> 
 + 
 +**V1 - Updated version** (middle of August 2016 - present) \\ 
 +//From printer received September 2, 2016// \\ 
 +{{:​mp_select_mini-main_board_rev2.jpg?​500|}} 
 +\\ 
 + 
 +*/ 
 + 
 +</​WRAP>​ 
 +</​WRAP>​ 
 + 
 + 
 +---- 
 + 
 +==== GPIO Header ==== 
 + 
 +<WRAP group> 
 +<WRAP column half> 
 + 
 +**GPIO Header** (V1 & V2) \\ 
 +//Picture taken April 20, 2018// - The arrows are pointing to the location of the unused GPIO header. It is reserved for future use and doesn'​t have any use at this time for the end user. It can be used to for simple diagnostics. \\ 
 +{{:​parts:​gpio_headers_on_v1_and_v2_m200_mainboards-01.jpg?​500|}} \\ 
 +\\ 
 + 
 + 
 +</​WRAP>​ 
 +<WRAP column half> 
 + 
 +**GPIO Header** V1 mainboard \\ 
 +{{:​parts:​gpio_header_mp_select_mini_v1_mainboard-01.jpg?​300|}} \\ 
 +\\ 
 + 
 + 
 +</​WRAP>​ 
 +</​WRAP>​ 
 + 
 + 
 +---- 
 + 
 +<WRAP group> 
 +<WRAP column half> 
 + 
 +===== Replacements ===== 
 + 
 +==== V1 ==== 
 +**GigDigit** - **[[https://​gigdigit.com/​mainboard-mp-select-mini-v1-v2-adjustable-stepper-drivers/​|Mainboard - MP Select Mini V1 with Adjustable Stepper Drivers]]** \\ 
 + 
 + 
 +==== V2 ==== 
 + 
 +**GigDigit** - **[[https://​gigdigit.com/​mainboard-mp-select-mini-v2-unmodified-see-description/​|Mainboard - MP Select Mini V2 (unmodified)]]** 
 + 
 + 
 +</​WRAP>​ 
 + 
 +<WRAP column half> 
 + 
 + 
 +/* 
 + 
 +**V1/V2 - Adjustable Driver Edition** \\  
 + 
 + 
 +(Board can work with V1 but needs a V2 display cable. Also needs a smaller plug for the hotend fan or converter to reduce the plug size. \\ 
 + 
 + 
 +{{ :​parts:​mainboard-replacement-mp-select-mini-v1-v2-adjustable-stepper-drivers_wiki-01.jpg?​500 |}} 
 + 
 +*/ 
 + 
 +</​WRAP>​ 
 +</​WRAP>​ 
 + 
 + 
  
-==== Malyan Systems ==== 
-sales1@malyansys.com (try first) \\ 
-sales2@malyansys.com \\ 
-support@malyansys.com 
parts/mainboard.1478044143.txt.gz · Last modified: 2016/11/01 23:49 by Matthew Upp