Malyan M200 3D Printer

User Tools

Site Tools

You are here: Malyan M200 3D Printer » Replacement Parts
replacements_parts

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
replacements_parts [2018/01/28 08:36]
Matthew Upp 		replacements_parts [2021/09/10 09:14] (current)
Matthew Upp
Line 1: Line 1:
 ===== Replacement Parts ===== ===== Replacement Parts =====
 +<WRAP group>
 +<WRAP half column>
  
     * [[parts:bearings|Bearings]]     * [[parts:bearings|Bearings]]
     * [[parts:belts|Belts]]     * [[parts:belts|Belts]]
-    * [[parts:ptfe_tubes|Bowden Tubes]]+    * [[parts:ptfe_tubes|Bowden Tube]]
     * [[parts:bowden_tube_connectors|Bowden Tube Connectors]]     * [[parts:bowden_tube_connectors|Bowden Tube Connectors]]
 +    * [[parts:cup_washers_and_spring|Cup Washers & Spring]]
 +    * [[parts:lcd_screen|Display]]
     * [[parts:endstops|Endstops]]     * [[parts:endstops|Endstops]]
 +    * [[https://gigdigit.com/extended-bed-120-x-245mm-print-area-for-select-mini-limited-supply/|GigDigit Extended Bed]]
     * [[parts:extruder|Extruder / Feed Mechanism]]     * [[parts:extruder|Extruder / Feed Mechanism]]
     * [[parts:fan_hotend|Fan for Hotend]]     * [[parts:fan_hotend|Fan for Hotend]]
 +    * [[parts:fan_mainboard|Fan for Mainboard - V2]]
     * [[parts:heater_block|Heater Block]]     * [[parts:heater_block|Heater Block]]
     * [[parts:heater_block_insulation|Heater Block Insulation & Tape]]     * [[parts:heater_block_insulation|Heater Block Insulation & Tape]]
     * [[parts:heat_bed|Heat Bed]]     * [[parts:heat_bed|Heat Bed]]
 +    * [[parts:heat_bed_rewire_kit|Heat Bed Rewire Kit]]
     * [[parts:screws_heat_bed|Heat Bed Leveling Screws]]     * [[parts:screws_heat_bed|Heat Bed Leveling Screws]]
     * [[parts:heat_break|Heat Break / Throat]]     * [[parts:heat_break|Heat Break / Throat]]
-    * [[parts:heatsink|Heatsink - V1]] +    * [[parts:heatsink|Heatsink - V1 & V2]] 
-    * [[parts:hotend|Hotend - Aftermarket Kits]]+    * [[parts:hotend|Hotends]]
     * [[parts:lcd_screen|LCD Screen]]     * [[parts:lcd_screen|LCD Screen]]
     * [[parts:mainboard|Mainboard / Motion Controller]]     * [[parts:mainboard|Mainboard / Motion Controller]]
Line 26: Line 33:
     * [[parts:screws_heat_sink|Set Screw & Square Nut - Heat Break and Bowden Connector]]     * [[parts:screws_heat_sink|Set Screw & Square Nut - Heat Break and Bowden Connector]]
     * [[parts:screws_heat_bed|Screws - Heat Bed]]     * [[parts:screws_heat_bed|Screws - Heat Bed]]
 +    * [[parts:silicone_adhesive|Silicone Adhesive]]
     * [[parts:stepper_motors|Stepper Motors]]     * [[parts:stepper_motors|Stepper Motors]]
     * [[parts:thermistors|Thermistors]]     * [[parts:thermistors|Thermistors]]
Line 32: Line 40:
     * [[parts:ui_controller_board|UI Controller Board]]     * [[parts:ui_controller_board|UI Controller Board]]
     * [[parts:wire_connectors|Wire Connectors]]     * [[parts:wire_connectors|Wire Connectors]]
 +    * [[parts:heat_bed_rewire_kit|Wire Kit for Heat Bed]]
     * [[thingiverse:x-axis-endcap|X-Axis Endcap]]     * [[thingiverse:x-axis-endcap|X-Axis Endcap]]
     * [[parts:z-axis_threaded_rod|Z-Axis Threaded Rod]]     * [[parts:z-axis_threaded_rod|Z-Axis Threaded Rod]]
- 
  
 ---- ----
  
-For direct replacement parts, check out **[[https://gigdigit.com|GigDigit.com]]** \\+</WRAP> 
 + 
 +<WRAP half column> 
 + 
 +For direct replacement parts and some not listed above or to the left, check out **[[https://gigdigit.com|GigDigit.com]]** \\
 [[https://gigdigit.com|{{:wiki:logo_-_dot_com_-_2050_x_650.png?nolink&250}}]] [[https://gigdigit.com|{{:wiki:logo_-_dot_com_-_2050_x_650.png?nolink&250}}]]
 +
 +</WRAP>
 +</WRAP>
 +
  
  
replacements_parts.1517128565.txt.gz · Last modified: 2018/01/28 08:36 by Matthew Upp

Page Tools

Except where otherwise noted, content on this site is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
CC Attribution-Noncommercial-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki