User Tools

Site Tools


wifi:g-code_file

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Last revision Both sides next revision
wifi:g-code_file [2017/06/29 13:47]
Matthew Upp corrected some typos
wifi:g-code_file [2020/05/21 23:09]
Matthew Upp
Line 27: Line 27:
  
 <file gcode wifi_setup.gcode>​ <file gcode wifi_setup.gcode>​
-; G-Code generated by Matthew Upp +; G-Code generated by Matthew Upp of GigDigit.com 
-; WiFi SSID & Password ​for Malyan M200 MP Select Mini +; 
-+; Set WiFi SSID & Password 
 +
 +; This gcode file will work with the following 3D printers: 
 +Malyan ​- M100, M200, M300, M310, M320, MA10, MA10 Mini 
 +; Monoprice - MP10, MP10 Mini, MP Mini Delta, ​MP Select Mini 
 +; 
 +;
 ; Look below and replace "​SSID"​ with the name of your WiFi network - don't leave spaces after the SSID name ; Look below and replace "​SSID"​ with the name of your WiFi network - don't leave spaces after the SSID name
 ; Look below and replace "​PASSWORD"​ with the password for your WiFi network - don't leave spaces after the password ; Look below and replace "​PASSWORD"​ with the password for your WiFi network - don't leave spaces after the password
 ; This method will not work if WiFi password contains a semicolon “;” ; This method will not work if WiFi password contains a semicolon “;”
 ; This method will not work for configuring open system WiFi networks with no password ; This method will not work for configuring open system WiFi networks with no password
-; Lines with only a semicolon are for making line separations only +
-; Please add a blank line to the end of the file while editing. DokuWiki Code Blocks deletes blank lines at the end of the block but g-code files should ​end with a single blank line at the end.+; Lines with only a semicolon are for making line separations only. 
 +; Please add a blank line to the end of the file while editing. 
 +; If you don't add the blank line but the print  
 +; completed screen will not appear and will require turning the  
 +; printer off and back on to proceed.  
 +; (DokuWiki Code Blocks deletes blank lines at the end of the block but  
 +g-code files typically ​end with a single blank line at the end.
 +
 +; This file is much longer than it needs to be but is like this to  
 +; show what is going on. 
 +
 +; If when "​printing"​ this file it does not show as completed on the  
 +; display but the fan pulsed on and off a few times then the commands  
 +; to set the SSID and password were successfully ran and saved.  
 +; You can turn the printer off and on. 
 +;
  
-;  +
-M106 S0 ; turn fan off in case it was already on +; BEGIN 
-M106 S200 ; turn fan on to signify start +M107 ; turn fan off in case it was already on 
-G28 X Y home X & Y to signify start +M106 S237 ; turn fan on to signify start 
-;  +
- +
 +The next two lines are the only actual commands that are needed to 
 +; store the wifi networks SSID and password.
 M550 SSID M550 SSID
 M551 PASSWORD M551 PASSWORD
-;  +
-;  +
-G1 X60 Y60 F1000 CENTER bed to signify completion +PULSE FAN TO SIGNIFY COMPLETION 
-M106 S0 ; turn fan off to signify completion+M107 ; turn fan off 
 +G4 S1 ; wait 1 second 
 +M106 S255 ; fan at full speed 
 +G4 P500 ; wait 0.5 seconds 
 +M107 ; fan off 
 +
 +G4 P250 ; wait 0.25 seconds 
 +M106 S255 ; fan at full speed 
 +G4 P500 ; wait 0.5 seconds 
 +M107 ; fan off 
 +
 +G4 P250 ; wait 0.25 seconds 
 +M106 S255 ; fan at full speed 
 +G4 P500 ; wait 0.5 seconds 
 +M107 ; fan off 
 +
 +G4 P250 ; wait 0.25 seconds 
 +M106 S255 ; fan at full speed 
 +G4 P500 ; wait 0.5 seconds 
 +M107 ; fan off 
 +
 +G4 P250 ; wait 0.25 seconds 
 +M106 S255 ; fan at full speed 
 +G4 P500 ; wait 0.5 seconds 
 +M107 ; fan off 
 +
 +G4 P250 ; wait 0.25 seconds 
 +M106 S255 ; fan at full speed 
 +G4 P500 ; wait 0.5 seconds 
 +M107 ; fan off 
 +
 +
 +M400 ; wait for current moves to finish 
 +M107 ; turn fan off to signify completion
 M84 ; disable motors M84 ; disable motors
 +; END
  
 </​file>​ </​file>​
wifi/g-code_file.txt · Last modified: 2020/05/22 00:02 by Matthew Upp